SikaSeal®-128
Multipurpose neutral silicone sealant.
SikaSeal®-128 is a 1-component, non-corrosive sealant for indoor and outdoor applications.
- Good UV and weathering resistance.
- Primerless adhesion to a wide range of substrates.
- High elasticity and flexibility.
- Low odor, neutral curing.
- Non-corrosive.
Usage
SikaSeal®-128 is designed for weatherproof joint between various substrates such as glass, metals, painted surfaces, aluminum, wood, ceramic tile.- Window and door installation.
- Tile parameter joints.
- General joint sealing.
Advantages
- Good UV and weathering resistance.
- Primerless adhesion to a wide range of substrates.
- High elasticity and flexibility.
- Low odor, neutral curing.
- Non-corrosive.
Packaging
~ 280ml(420g) cartridge (basic colors), 12 cartridges per box
~ 280ml (280g) cartridge (transparent color).
~ 600ml (900g) sausage (basic colors), 20 sausages per box.
~ 600ml(600g) sausage (transparent color), 20 sausages per box.
Colour
- White
- Transparent
- Grey
- Black
- Others on request
Product Details
Chemical base
Neutral silicone.
Shelf life
SikaSeal®-128 has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Storage conditions
Store in dry conditions, upside down and protected from direct sunlight and at temperatures below +27 °C.
Density
~1.45-1.55 kg/l (Basic colors).
~0.95-1.05 kg/l (Transparent color). (ISO 1183-1)
Shore A Hardness
~30-50 (Basic colors) (ISO 868)
~20-30 (Transparent color)
Tensile Strength
~1.0 MPa (Basic colors). (ISO 8339)
~0.5 MPa (Transparent color).
Elongation at break
≥ 250% (basic colors) (ISO 37)
≥ 200% (transparent color)
Movement Capability
± 25% (basic colors) (ASTM C719)
± 20% (transparent color)
Elastic Recovery
> 80 % (ISO 7389)
Service temperature
-40 °C min. / +150 °C max.
Joint Design
The joint width must be designed to suit the joint movement required and the movement capability of the sealant. For joints ≥ 10 mm and ≤ 20 mm wide, a joint depth of 10 mm is recommended.
For larger joints please contact our Technical Service Department.
Application
Ambient Air Temperature
+5 °C min. / +40 °C max.
> 3 °C above dew point.
Substrate Temperature
+5 °C min. / +40 °C max.
> 3 °C above dew point.
Curing Rate
~3 mm / 24 hours (23 °C / 50 % r.h.) (CQP 049-2)
Skin Time / Laying Time
20-50 minutes (basic colors) (23 °C / 50 % r.h.) (CQP 019-1)
05-15 minutes (transparent color)
Consumption
Joint Width Joint Depth Joint Length / 280 ml
6 mm 4 mm ~11.7 m
9 mm 5 mm ~6.2 m
12 mm 6 mm ~3.9 m
20 mm 10 mm ~1.4 m
SUBSTRATE PREPARATION
The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, old sealants and poorly bonded paint coatings which could affect adhesion of the sealant. The substrate must be of sufficient strength to resist the stresses induced by the sealant during movement.
All dust, loose and friable material must be completely removed from all surfaces using suitable equipment before application of any activators, primers or sealant.
SikaSeal®-128 adheres without primers and/or activators.
For optimum adhesion, joint durability and critical, high performance applications such as joints on multistorey buildings, highly stressed joints, extreme weather exposure or water immersion / exposure, the following priming and/or pre-treatment procedures must be followed:
Non-porous substrates
Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles.Slightly roughen surface with a fine abrasive pad.
Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth.
Before sealing, allow a waiting time of > 15 minutes (<6 hours).
Other metals, such as brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours), apply Sika® Primer-3 N by brush. Before sealing, allow a waiting time of > 30 minutes (< 8 hours) PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Before sealing, allow a waiting time of > 30 minutes (< 8 hours).
Glass must be cleaned with Isopropanol before application.
Porous substrates
Porous substrates must be primed using Sika® Primer-3 N applied by brush.
Before sealing, allow a waiting time of > 30 minutes (<8 hours).
Adhesion tests on project specific substrates must be performed and procedures agreed with all parties before
full project application.
For more detailed advice and instructions contact Sika Technical Services.
Note: Primers and activators are adhesion promoters and not an alternative to improve poor preparation / cleaning of the joint surface. Primers also improve the long term adhesion performance of the sealed joint.
CLEANING OF TOOLS
Clean all tools and application equipment with Sika® Remover-208 immediately after use. Hardened material can only be removed mechanically. For cleaning skin, use Sika® Cleaning Wipes-100.