Product Data Sheet Show all documents
SikaCeram®-200 HP

SikaCeram®-200 HP

Prepacked cementitious tile adhesive

SikaCeram®-200 HP is a cementitious water resistant tile adhesive that is specially formulated for floor &  wall tiling on concrete, rendered surface  and both internal and external applications. The product is ideal for installation ceramic tiles, homogeneous tiles, mosaics, marble and granites.

  • Easy application (Adding the required water content)
  • Water resistant, can be used in wet areas such as toilets, kitchen
  • Excellent pull-off strength
  • Soaking of tiles in water before installation is not required
  • Consistency quality
  • Convenient in placing, handing, mixing and application
  • Weather resistant and durable
Product Data Sheet Show all documents

Usage

SikaCeram®-200 HP can be used as thin bed or thick bed adhesive for items as below:
  • Toilet
  • Kitchen
  • Rendered brick wall
  • External wall
  • Balcony
  • Swimming pool
  • Pre-cast components
 

Advantages

  • Easy application (Adding the required water content)
  • Water resistant, can be used in wet areas such as toilets, kitchen
  • Excellent pull-off strength
  • Soaking of tiles in water before installation is not required
  • Consistency quality
  • Convenient in placing, handing, mixing and application
  • Weather resistant and durable

Packaging

25 kg per bag

Colour

Grey/ White powder

Product Details

Product Information

Chemical base

Cement, graded sand, several admixtures

Shelf life

9 months from date of production if stored properly in unopened, original packaging

Storage conditions

Dry, cool, shaded place.

Density

1,300-1,600 kg/m³ (density of fresh mortar)
Technical Information

Tensile Adhesion Strength

Tensile adhesion bond strength

≥ 1 N/mm² (28 days)

Tensile adhesion strength after water immersion

≥ 1 N/mm² (28 days)

Tensile adhesion strength after heat aging

≥ 1 N/mm² (28 days)

Application

Application Information

Mixing ratio

Approx. 5.5 L to 6.5 L of clean water per 25 kg bag

Substrate Temperature

Minimum 8°C
Maximum 40°C

Pot Life

30-45 minutes (at 27°C / 65% r.H)

Open time

≥ 0.5 N/mm²

(After not less than 30 mins)

Adjustability Time

Approx. 20 minutes

Curing time

Waiting time before grouting:
For wall – after 7 to 8 hours (depending on temperature)
For floor – after 24 hours
Open to full traffic - after 14 days
Consumption

Consumption

~7-8 m² per 25 kg bag (based on 2mm mortar thickness)

Yield

25 kg SikaCeram®-200 HP powder bag yields approx. 16.2 L of mortar
Approx. 62 bags required for 1 (one) m³ of mortar
Application steps

MIXING

  • Pour powder SikaCeram®-200 HP into 6-7 L clean water containers
  • Mixing by machenical mixer, producing a homogeneous paste with a good workability.
  • Mix thoroughly using mechanical mixer for 3-5 minutes until a homogeneous lump-free paste is achived
  • Allow the mix to stand for 1-2 minutes and thoroughly re-mix for another 1 minute before using.

APPLICATION

  • Pour a litte tile adhesive on the substrate. Use a notched trowel spread tile adhesive on the substrate.

               For floor: spread out the floor surface mortar

               For wall: plastering horizontally

  • To increase adhesion and coverage should be constructed at layer of motar at the back of the tiles.
  • Place the tiles on motar, firm pressure to ensure the tiles are clinging to the motar.
  • Any adjustment of tile should be done within 20 minutes after application. The wet mix should be used within the 30 to 45 minutes, depending on the ambient temperature.

CLEANING OF TOOLS

Remove non-hardened SikaCeram®-200 HP products from tools and equipment with water. Hardened material can only be removed mechanically.

 

Documents