Sikalastic®-500 Acrylic Primer AP
1-PART WATER BASED ACRYLIC PRIMER
Sikalastic®-500 Acrylic Primer AP is a 1-part, water-based, acrylic primer to prepare surfaces prior to the application of liquid applied waterproofing membranes and wall coating systems.
- Easy to apply
- Applied by brush or roller
- Fast drying
- Improves adhesion of the liquid applied membrane to the substrate
- High torelence to moist level of substrate
Usage
The Product is used as a:- Primer and bonding agent on smooth concrete finishes
- Primer for absorbent surfaces for water-based Sikalastic® roofing systems
- Dust reducer and to increase abrasion resistance of the substrate
- Pore sealer on rough porous concrete to eliminate air bubbles
Advantages
- Easy to apply
- Applied by brush or roller
- Fast drying
- Improves adhesion of the liquid applied membrane to the substrate
- High torelence to moist level of substrate
Packaging
20Kg container
Colour
Liquid | milky white |
Dried | transparent |
Product Details
Chemical base
Water-based acrylic
Shelf life
12 months
Storage conditions
The product must be stored in original, unopened and undamaged packaging in dry conditions at temperatures between +5 °C and +30 °C.
Always refer to packaging.
Density
(1.00 ± 0.05) kg/L (at +23 °C) | (EN ISO 2811-1) |
Application
Ambient Air Temperature
Maximum | +40 °C |
Minimum | +5 °C |
Relative Air Humidity
80 % maximum
Dew Point
Beware of condensation. The substrate and uncured applied roof material must be at least +3 °C above dew point to reduce the risk of condensation on the surface finish.
Substrate Temperature
Maximum | +40 °C |
Minimum | +5 °C |
Substrate Moisture Content
≤ 6 % parts by weight.
The substrate must be visibly dry with no standing moisture.
The following test methods can be used: Sika®-Tramex meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene sheet).
Waiting Time / Overcoating
30 minutes
Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.
Consumption
0.2–0.3 kg/m2 per coat
Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.
SUBSTRATE PREPARATION
GENERAL
-
Substrates must be free of standing water (no puddles) clean and free of all contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
-
All dust, loose and friable material must be completely removed from all surfaces before application of the Product, and associated system products, by industrial vacuuming equipment.
-
To confirm adequate surface preparation and Product adhesion, carry out a small trial before full application together with adhesion tests.
CEMENTITIOUS SUBSTRATES
-
Substrate must be sound with a minimum tensile adhesion strength of 1.5 N/mm2, clean, dry and free of all contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
-
New concrete must be cured for at least 28 days and have a tensile strength > 1.5 N/mm2.
-
Cementitious substrates must be prepared mechanically using substrate preparation equipment to remove cement laitance and achieve an open textured gripping surface profile suitable for the product thickness.
-
High spots can be removed by grinding.
-
Weak cementitious substrates must be removed and surface defects such as blow holes and voids must be fully exposed.
-
Repairs to the substrate, filling of joints, blowholes / voids and surface levelling must be carried out using appropriate products from the Sikafloor®, Sikadur® and Sikagard® range of materials. Products must be cured before applying Sikalastic®-500 Acrylic Primer AP.
BRICK AND STONE
-
Mortar joints must be sound and flush pointed.
-
Replace loose bricks, stone and mortar.
-
Thoroughly clean the surface by power washing and allow to dry.
UNGLAZED CERAMIC TILES
-
Ensure all tiles are securely fixed.
-
Replace any broken, loose or missing sections.
-
Thoroughly clean the surface by power washing and allow to dry.
CLAY TILES
-
Ensure all tiles are securely fixed.
-
Replace any broken, loose or missing sections.
-
Thoroughly clean the surface by power washing and allow to dry.
MIXING
Product is supplied ready to use
IMPORTANT
Avoid over-mixing to minimise air entrainment.
Before application, mix for at least 1 minute or until the liquid is uniform.
Note: Use an electric single or double paddle mixer (300–400 rpm) with spiral paddle for mixing.
APPLICATION
IMPORTANT
Protect from rain
After application, the product must be protected from heavy rain or rain showers until dry to prevent surface damage.
- Apply Sikalastic®-500 Acrylic Primer AP to the clean substrate with roller or brush.
- Allow to dry until clear film appears.
- Primer is dry when all milkiness disappears.
- In the case of very porous substrates apply a second coat.
Note: Always confirm waiting / overcoating times have been achieved and the surface is totally dry without pinholes before applying successive coats of products. Remove surface water between coating applications.